DEVELOPMENT OF AN IMPROVED TECHNOLOGY FOR ENAMELING TEMPERED GLASS SAMPLES AND INVESTIGATION OF THE TECHNOLOGICAL PROPERTIES OF THE OBTAINED SAMPLES
Keywords:
tempered glass, glass enamel, thermal treatment, tempering temperature, physical and mechanical properties, enamel coating, sheet glass, technological scheme.Abstract
This article presents the results of developing an improved technology for enameling the surface of tempered glass, determining the optimal parameters of the technological process, and evaluating the physical and mechanical properties of the obtained samples. In the study, the processes of thermal tempering and enamel coating formation were investigated under laboratory conditions using flat sheet glass samples. The tempering temperature was determined based on the viscosity characteristics of glass and the Vogel–Fulcher–Tammann equation. According to the experimental results, the optimal tempering temperature was found to be 693 °C, with a holding time of 4 minutes. During the cooling stage, the use of compressed air at a pressure of 6 kPa enabled the formation of the required internal stresses within the glass body. The bending strength of the tempered samples increased significantly compared to non-tempered samples, reaching values in the range of 310–340 MPa. In addition, the physical and mechanical properties of the enameled tempered glass samples were determined, confirming their compliance with GOST standards. The obtained results demonstrate the feasibility of producing high-quality enameled tempered glass based on locally available raw materials.
References
Shelby, J. E. (2005). Introduction to Glass Science and Technology. Royal Society of Chemistry.
Buranova D.B. Main characteristics of quartz-feldspar sands from the Khiva deposit, and the physico-chemical and technological fundamentals of obtaining an enriched concentrate. Kompleksnoe Ispolzovanie Mineralnogo Syra = Complex Use of. Mineral Resources. 2027; 340(1): 37-44. https://doi.org/10.31643/2027/6445.04
Yunusov M.Y., Babaev Z.K., Kurambaev Sh.R. Matchanov Sh.K. The Enrichment of Quartz Sands of the Khiva Deposit for Glass Production. International Journal of Materials and Chemistry 2023, 13(2): P:, 19-22. DOI: 10.5923/j.ijmc.20231302.01.
Babaev Z. K., Matchonov Sh. K., Buranova D.B., Iskandarov O.D., Ibodullayev B. O., Pirnafasov A.A. Condition and Development of the Uzbekistan’s Glass Industry. International Journal of Advanced Research in Science, Engineering and Technology Volume 5, Issue 11, ISSN: 2350-0328 www.ijarset.com, November 2018-С.7270-7273
Doremus, R. H. (1994). Glass Science. Wiley.
Buranova D.B., Yunusov M.Y., Babaev Z.K., Kurambaev Sh.R., Atashev E.A. The Physico–Chemical Analysis of Quartz Sand of “Khiva” Deposit. RA Journal of applied research. ISSN: 2394-6709. DOI:10.47191/rajar/v9i10.01. Vol: 09 Issue: 10 October-2023. P:,506-509.
Gardon, R. (1985). Thermal tempering of glass. Journal of the American Ceramic Society, 68(10), 495–502.
Nielsen, J. H., & Olesen, J. F. (2012). Structural behavior of tempered glass. Engineering Structures, 36, 137–145.
Haldimann, M., Luible, A., & Overend, M. (2008). Structural Use of Glass. IABSE.
Karlsson, S. (2010). Strength of thermally tempered glass. Glass Performance Days Proceedings, 45–50.
Eppler, R. A., & Eppler, D. R. (2000). Glazes and Glass Coatings. American Ceramic Society.
Taylor, J. R., & Bull, A. C. (1986). Ceramic Glaze Technology. Pergamon Press.
Kingery, W. D., Bowen, H. K., & Uhlmann, D. R. (1976). Introduction to Ceramics. Wiley.
Levin, E. M., Robbins, C. R., & McMurdie, H. F. (1964). Phase Diagrams for Ceramists. American Ceramic Society.
Callister, W. D., & Rethwisch, D. G. (2020). Materials Science and Engineering: An Introduction. Wiley.
Ashby, M. F., & Jones, D. R. H. (2012). Engineering Materials 1. Elsevier.
Lawn, B. (1993). Fracture of Brittle Solids. Cambridge University Press.
Wiederhorn, S. M. (1967). Influence of water vapor on crack propagation in glass. Journal of the American Ceramic Society, 50(8), 407–414.
Vogel, H. (1921). The temperature dependence law of viscosity. Physikalische Zeitschrift, 22, 645–646.
Fulcher, G. S. (1925). Analysis of recent measurements of the viscosity of glasses. Journal of the American Ceramic Society, 8(6), 339–355.
Tammann, G., & Hesse, W. (1926). The dependence of viscosity on temperature. Zeitschrift für anorganische Chemie, 156, 245–257.
Cable, M. (1998). Glass Manufacturing Processes. Springer.
McMillan, P. W. (1979). Glass-Ceramics. Academic Press.
Brow, R. K. (2000). Review: Structure of simple phosphate glasses. Journal of Non-Crystalline Solids, 263–264, 1–28.
Shelby, J. E. (2009). Glass Formation and Processing. Wiley.
ГОСТ 30698-2014 – Закалённое стекло. Методы испытаний.
ГОСТ 33891-2016 – Стекло эмалированное. Технические требования.
ГОСТ Р 52569-2018 – Коэффициент термического расширения стекла.
ГОСТ 24405-80 – Методы определения свойств стекла.
Zhang, X., et al. (2018). Mechanical properties of tempered glass. Construction and Building Materials, 186, 114–121.
Chen, S., et al. (2020). Enamel coatings on glass substrates. Surface & Coatings Technology, 385, 125412.
Li, Y., et al. (2019). Thermal stress analysis in glass tempering. Journal of Materials Processing Technology, 271, 264–272.
Downloads
Published
How to Cite
Issue
Section
License

This work is licensed under a Creative Commons Attribution 4.0 International License.
Articles published in IQRO — Scientific Methodological Journal are licensed under the Creative Commons Attribution 4.0 International License (CC BY 4.0).
Authors retain copyright and grant the journal the right of first publication.
Users may read, download, copy, distribute, print, search, or link to the full texts of articles, provided that the original authors and the journal are properly cited.
Published materials may be used, distributed, and reproduced in any medium, provided that the original work is properly cited.



Uzbekistan
Türkiye
Kazakhstan
Kyrgyzstan
Turkmenistan
Azerbaijan
India
Republic of Korea
Japan
United States of America
Kosovo